# Engineering/Civil Engineering -MCQS-Hydraulics Section 4 Sample Test,Sample questions

## Question: ``` Centre of buoyancy is```

1.centroid of the floating body

2. centroid of the fluid displaced

3.centre of pressure of the displaced liquid

4.none of these.

Posted Date:-2021-05-21 10:30:02

## Question: ``` For critical flow, the Froude number is :```

1.1

2.. less than 1.0

3.more than 1.0

4.2

Posted Date:-2021-05-21 10:30:02

## Question: ``` In an inclined position, a venturimeter records```

4. none of these.

Posted Date:-2021-05-21 10:30:02

## Question: ``` A floating body attains stable equilibrium if its metacentre is```

1.at the centroid

2.above the centroid

3.below the centroid

4.anywhere.

Posted Date:-2021-05-21 10:30:02

## Question: ``` An open container filled with water is moved vertically upward with a uniform linear acceleration. The pressure at its bottom will be```

1.greater than static pressure

2.equal to static pressure

3.lesser than static pressure

4.none of these.

Posted Date:-2021-05-21 10:30:02

## Question: ``` An orifice is called a large orifice if water head, is```

1.twice the diameter of the orifice

2. thrice the diameter of the orifice

3. four times the diameter of the orifice

4.five times the diameter of the orifice.

Posted Date:-2021-05-21 10:30:02

## Question: ``` For the two dimensional flow, the stream function is given by Ïˆ = 2xy. The velocity at a point (3, 4) is```

1.6 m/sec

2.8 m/sec

3.10 m/sec

4.12 m/sec

Posted Date:-2021-05-21 10:30:02

## Question: ``` In a short cylindercial external mouthpiece, the venacontracta occurs at a distance from the outlet of orifice equal to```

1.diameter of the orifice

2.one-fourth the diameter of the orifice

3.one-third the diameter of the orifice

4.two-third the diameter of the orifice

Posted Date:-2021-05-21 10:30:02

## Question: ``` In a two dimensional flow if the components of the velocity are u = ax ; v = by, the point where no motion occurs, is known as```

1.critical point

2. neutral point

3.stagnation point

4.stationary point

Posted Date:-2021-05-21 10:30:02

## Question: ``` Most economical section of a circular channel for maximum velocity, is if,```

1.depth of water = 0.810 diameter

2.hydraulic mean depth = 0.304 diameter

3.wetted perimeter = 2.245 diameters

4.all the above.

Posted Date:-2021-05-21 10:30:02

## Question: ``` The centre of pressure of a vertical plane immersed in a liquid is at```

1.centre of higher edge

2. centre of lower edge

3.centroid of the area

4.none of these.

Posted Date:-2021-05-21 10:30:02

## Question: ``` The dimensionless parameter not applicable to flowing liquids, is```

1.Reynold number

2.Weber number

3.Pressure coefficient

4.Kinematic viscosity

Posted Date:-2021-05-21 10:30:02

## Question: ``` The flow in a channel is said to be non-uniform, if```

1.free water surface of an open channel is not parallel to the bed of channel

2.head needed to overcome frictional reistance is less than the drop in elevation of channel bed

3.head needed to overcome frictional resistance is more than the drop in elevation of channel bed

4.all the above.

Posted Date:-2021-05-21 10:30:02

## Question: ``` The gases are considered incompressible if Match number is```

1.equal to 1.0

2.equal to 1.5

3. is more than 0.5

4.less than 0.2

Posted Date:-2021-05-21 10:30:02

## Question: ``` The intensity of pressure due to sudden closure of a valve of a pipe in which water flows with velocity v, is directly proportional to :```

1.square root of the bulk modulus of elasticity of water

2.bulk modulus of elasticity of water

3. specific weight of water

4.none of these.

Posted Date:-2021-05-21 10:30:02

## Question: ``` The width of a weir with end contraction, is```

1.equal to the width of the channel

2.less than the width of the channel

3. half the width of the channel

4.none of these.

Posted Date:-2021-05-21 10:30:02

## Question: ``` Though angle of deviation of liquid is more in internal mouth piece, the contraction of the jet, is```

1.more in the internal mouth piece

2. less in the internal mouth piece

3.equal to external mouth piece

4.none of these.

Posted Date:-2021-05-21 10:30:02

## Question: `A body of dimensions 1.5 m x 1.0 m x 2 m weighs 3000 kg in water. Its specific gravity is`

1.0.8

2.0.9

3.1

4.1.1

Posted Date:-2021-05-21 10:30:02

## Question: `A stepped notch is a combination of`

1.rectangular notches of different sizes

2.triangular notches of different sizes

3.rectangular and triangular notches

4. all the above.

Posted Date:-2021-05-21 10:30:02

## Question: `Flow net' can be drawn only if the flow is`

1.turbulent

2.rotational

3.distortion

4.none of these.

Posted Date:-2021-05-21 10:30:02

## Question: `For a most economical rectangular channel, the width of the channel must be`

1.equal to depth of flow

2.twice the depth of flow

3.half the depth of flow

4.None of these.

Posted Date:-2021-05-21 10:30:02

## Question: `If the pressure at the inlet of a pipe is 90 kg/cm2 and pressure drop over the pipe line is 10 kg/cm2, the efficiency of transmission, is`

1.66.60%

2.77.70%

3.55.50%

4.88.8%.

Posted Date:-2021-05-21 10:30:02

## Question: `In an inclined pipe, the pressure difference at its two ends is due to`

4.all the above.

Posted Date:-2021-05-21 10:30:02

## Question: `In C.G.S. system the unit of visocity is`

1.dyne

2.joule

3.poise

4.newton

Posted Date:-2021-05-21 10:30:02

## Question: `In steady flow, which one of the following changes with time`

1.velocity

2.pressure

3.density

4.none of these.

Posted Date:-2021-05-21 10:30:02

## Question: `ï»¿Equation of continuity of flow is based on the principle of conservation of`

1.mass

2.momentum

3.force

4.none of these.

Posted Date:-2021-05-21 10:30:02

## Question: `Pick up the correct statement from the following :`

1. Discharge over a triangular notch is proportional to H5/2

2.Discharge over a rectangular notch is proportional to H3/2

3.Both (a) and (b)

4.Neither (a) nor (b).

Posted Date:-2021-05-21 10:30:02

## Question: `Pick up the incorrect statement from to following regarding triangular notch :`

1.For measuring low discharge, it gives more accurate result

2.Only one reading (i.e. H) is required for computation of discharge

3.Ventilation is necessary

4.None of these.

Posted Date:-2021-05-21 10:30:02

## Question: `The flow in open channel is laminar if the Reynold number is`

1.less than 500

2.more than 500

3.1000

4.none of these.

Posted Date:-2021-05-21 10:30:02

## Question: `The flow in open channel is said to be subcritical if the Froude number is`

1.less than 1.0

2.equal to 1.0

3.greater than 1.0

4.none

Posted Date:-2021-05-21 10:30:02

## Question: `The flow in which each liquid particle has a definite path and the paths of adjacent particles do not cross each other, is called`

1.stream line flow

2.uniform flow

4. turbulent flow.

Posted Date:-2021-05-21 10:30:02

## Question: `The hydrostatic force acts through`

1.centre of pressure

2.centre of top edge

3. centre of bottom edge

4.metacentre.

Posted Date:-2021-05-21 10:30:02

## Question: `The notch angle for maximum discharge over a triangular notch, is`

1.30Â°

2.60Â°

3.90Â°

4.120Â°

Posted Date:-2021-05-21 10:30:02

## Question: `The pressure rise due to water hammer depends upon`

1. the velocity of flow of water in the pipe

2.the length of pipe

3.time taken to close the valve

4.All of above.

Posted Date:-2021-05-21 10:30:02

## Question: `The unit of the viscosity is`

1.kg sec/m2

2.Newton sec per m2

3.Newton-sec2/m3

4. m2 per sec.

Posted Date:-2021-05-21 10:30:02

## Question: `Total energy line is`

4. All the above.

Posted Date:-2021-05-21 10:30:02

## Question: `Weber number is the ratio of inertia force to`

1.surface tension

2.gravitational force

3.elasticity

4.velocity

Posted Date:-2021-05-21 10:30:02

## Question: `When a liquid rotates at constant angular velocity about a vertical axis of a rigid body, the pressure`

1.increases linearly to its radial distance

2.varies inversely as the altitude along any vertical line

3. varies as the square of the radial distance

4.. decreases as the square of the radial distance

Posted Date:-2021-05-21 10:30:02

## More MCQS

##### R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!