Electrical measurements/Electrical Measurement MCQ Question Set 7 Sample Test,Sample questions

Question:
 Current can be measured effectively by making use of ____

1.d.c. voltmeter

2.a.c. ammeter

3.d.c. ammeter

4.a.c. voltmeter


Question:
 Energy meter can be directly used in measurement.

1.True

2.False

3.all of the above

4.None of the mentioned


Question:
 Input impedance depends on _____

1.resistance

2.capacitance

3.inductance

4. voltage


Question:
 Low voltage signals can be measured by _______

1.amplifiers

2. transformers

3. transformers

4.voltmeters


Question:
 Preliminary light load adjustment involves _______

1.applying rated voltage across current coil

2.making use of a light load

3.applying rated voltage across pressure coil

4.adjusting the light load


Question:
 Sensitivity is of the order of ______

1. MV

2. V

3.GV

4.mV


Question:
 Voltage ranges in a meter are _____

1. 5-10-15

2.20-50-100

3.0.5-1-1.5

4.1-3-10


Question:
 What is the effect of the input on the transistor Q2?

1.bias on Q2 decreases

2. bias on Q2 is constant

3. bias on Q2 is zero

4.bias on Q2 increases


Question:
A rotating phase sequence indicator consists of _____

1.1 coil

2.2 coils

3. 5 coils

4.3 coils


Question:
An electronic energy meter is advantageous compared to conventional ones.

1.True

2.False

3.all of the above

4.None of the mentioned


Question:
An electronic energy meter makes use of ______

1.IC

2.Transformer

3.CRO

4.Multimeter


Question:
Analog signal is converted _______

1. into oscillations

2. into digital

3.into pulses

4.into current


Question:
At high frequencies the capacitive reactance ____

1.is constant

2. increases

3.decreases

4.becomes zero


Question:
Average power is _______

1.product of voltage and current

2.product of average current and voltage

3.product of instantaneous voltage and current

4.product of absolute voltage and current


Question:
Average responding voltmeter is cheap and accurate.

1.True

2.False

3.all of the above

4.None of the mentioned


Question:
Basic circuit of multimeter consists ______

1.of a.c. amplifier

2. of d.c. amplifier

3.operational amplifier

4. power amplifier


Question:
Bridge is balanced by ______

1. galvanometer

2.oscillator

3.zero adjustment resistor

4.head phone


Question:
Creep adjustment involves _____

1.adjusting the creep

2.exciting the current coil

3.adjusting the turns ratio

4.exciting the pressure coil


Question:
Creeping in an energy meter can be found using ______

1.creep adjustment

2.preliminary light load adjustment

3.full load u.p.f adjustment

4. light load adjustment


Question:
Decibel covers a small range of values.

1. True

2.False

3.all of the above

4.None of the mentioned


Question:
Disc rotation is determined by ____

1.the supply voltage

2. an arrow

3.the turns ratio

4.the load current


Question:
Eddy e.m.f produces a torque.

1.True

2.False

3.all of the above

4.None of the mentioned


Question:
Electronic multimeter measures ______

1.voltage, current and resistance

2.voltage, current and resistance

3.current and power

4.energy and power


Question:
Excitation of the three coils produces _____

1.a static magnetic field

2.a rotating magnetic field

3. a static electric field

4. a rotating electric field


Question:
Frequency of oscillation in an electronic energy meter depends on ______

1. output current of multiplier

2. output voltage of multiplier

3.output power of multiplier

4.input resistance of multiplier


Question:
Full load u.p.f adjustment involves ______

1.adjusting the loads at unity power factor

2.applying rated voltage to pressure coil and a p.f. of unity for current coil

3.only applying rated voltage to pressure coil

4.only a p.f. of unity for the current coil


Question:
High range can be obtained in a basic D.C. electronic voltmeter by ________

1. a transformer

2.an attenuator

3.a transducer

4.a resistor


Question:
How many types of phase sequence indicators are there?

1.1

2.5

3.2

4.10


Question:
Input impedance of a voltmeter is ______

1.high

2.low

3.medium

4.zero


Question:
Input impedance of an electronic voltmeter is _____

1. low

2.high

3.medium

4. zero


Question:
Light load adjustment involves ________

1.applying rated voltage across the pressure coil

2.adjusting a light load

3.applying rated current across the transformer

4.applying rated voltage across the current coil


Question:
Linear meter with 1% accuracy must have ______

1.100 divisions

2.50 divisions

3. 200 divisions

4.500 divisions


Question:
Low power factor adjustment involves _____

1.adjusting the power factor at lower loads

2.applying rated voltage to pressure coil and a p.f. of 0.5 for current coil

3.only applying rated voltage to pressure coil

4.only a p.f. of 0.5 for the current coil


Question:
Measurement of energy involves _____

1.inductance and capacitance measurement

2.power consumption and time duration

3. resistance measurement and voltage drop

4. current consumption and voltage drop


Question:
Measurement of heat power ________

1.uses a heat sink

2. uses a thermometer

3.uses a thermocouple

4.uses a black body


Question:
Meter can be isolated from the circuit in a basic D.C. electronic voltmeter.

1.True

2.False

3.all of the above

4.None of the mentioned


Question:
Meter reading is obtained by _____

1.sensing voltage

2. sensing heat power

3.sensing current

4. sensing resistance


Question:
Noise is a function of ______

1. voltage

2.current

3.bandwidth

4.frequency


Question:
Overloading is ________

1.damages the meter

2. increases the temperature

3.doesn’t affect the meter

4.decreases the sensitivity


Question:
Phase sequence indicator gives the maximum value of phase voltages.

1.True

2. False

3.all of the above

4.None of the mentioned


Question:
R.M.S value means ______

1.root mean square

2.rate mean second

3.root median second

4.rate mode second


Question:
Response of thermocouples is fast.

1.True

2.False

3.all of the above

4.None of the mentioned


Question:
Sensitivity of electronic voltmeter is high.

1. True

2.False

3.all of the above

4.None of the mentioned


Question:
Sufficient heating of the heater is ensured by ______

1.increasing the temperature

2. making use of induction coil

3.amplifying d.c. input

4.amplifying a.c. input


Question:
Synchronization of A.C. supply means ________

1.different phase sequence

2.same phase sequence

3.zero phase

4.using a transformer


Question:
The three coils are _____

1.star connected

2.delta connected

3.not connected

4.shorted


Question:
What is basic range of a meter?

1.causes maximum deflection

2.causes minimum deflection

3.causes zero deflection

4.causes medium deflection


Question:
What is the main disadvantage of a true r.m.s responding voltmeter?

1. presence of transducer

2.presence of thermocouple

3.presence of transformer

4.presence of oscillator


Question:
What is the naming convention for the two thermocouples?

1.thermocouple 1 and thermocouple 2

2. input thermocouple and output thermocouple

3.measuring thermocouple and balancing thermocouple

4.internal thermocouple and external thermocouple


Question:
What is the role of a multiplier?

1. it multiplies the voltage and current

2.divides the alternating voltage and current

3.supplies instantaneous voltage and current

4.multiplies alternating voltage and current


More MCQS

  1. Electrical Measurement MCQ Question Set 1
  2. Electrical Measurement MCQ Question Set 2
  3. Electrical Measurement MCQ Question Set 3
  4. Electrical Measurement MCQ Question Set 4
  5. Electrical Measurement MCQ Question Set 5
  6. Electrical Measurement MCQ Question Set 6
  7. Electrical Measurement MCQ Question Set 7
  8. Electrical Measurement MCQ Question Set 8
  9. Electrical Measurement MCQ Question Set 9
  10. Electrical Measurement MCQ Question Set 10
  11. Electrical Measurement MCQ Question Set 11
  12. Electrical Measurement MCQ Question Set 12
  13. Electrical Measurement MCQ Question Set 13
  14. Electrical Measurement MCQ Question Set 14
  15. Electrical Measurement MCQ Question Set 15
  16. Electrical Measurement MCQ Question Set 16
  17. Electrical Measurement MCQ Question Set 17
  18. Digital Communications MCQs set-1
  19. Digital Communications MCQs set-2
  20. Digital Communications MCQs set-3
  21. Digital Communications MCQs set-4
  22. Digital Communications MCQs set-5
  23. Digital Communications MCQs set-6
  24. Digital Communications MCQs set-7
  25. Digital Communications MCQs set-8
  26. Digital Communications MCQs set-9
  27. Digital Communications MCQs set-10
  28. Digital Communications MCQs set-11
  29. Digital Communications MCQs set-12
  30. Digital Communications MCQs set-13
  31. Digital Communications MCQs set-14
  32. Digital Communications MCQs set-15
  33. Digital Communications MCQs set-16
  34. Digital Communications MCQs set-17
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!