After doing a low-level format what would be the next step in configuring the hard drive in a system?

  1. Home

- Online Exam Test Papers | - MCQs[multiple choice questions and answers ] | - Mock Test Papers | - Practice Papers | - Sample Test Papers |

Question:
After doing a low-level format what would be the next step in configuring the hard drive in a system?

1.Format DOS partition

2.Install operating system

3.Configure DMA channel and back-up interrupt

4.Partition had disk

Posted Date:-2021-02-20 12:26:55

More MCQS Questions and answers

  1. Most PCs give a single beep on bootup to indicate they are ok hardware wise. You boot your PC and don't get a beep. What should you check first?
  2. RS-232 is a standard that applies to:
  3. A numeric error code check: A 17xx indicates a problem with:
  4. The 34-pin connection on an I/O card is for?
  5. What command is used to reset a MODEM when using the "AT Command Set"?
  6. What is the first thing you could do to check for damage to a printer after receiving it?
  7. You were installing an application in Windows 95 and the computer crashes what do you do?
  8. A 25-pin female connector on the back of your computer will typically be:
  9. A hard disk is divided into tracks which are further subdivided into:
  10. A wrist grounding strap contains which of the following:
  11. After doing a low-level format what would be the next step in configuring the hard drive in a system?
  12. During boot-up the memory test:
  13. ESD would cause the most damage to which component?
  14. ESD would cause the most damage to which component?
  15. In Inkjet technology the droplets of ink are deflected by?
  16. In laser printer technology what happens during the conditioning stage?
  17. From what location are the 1st computer instructions available on boot up?
  18. Missing slot covers on a computer can cause?
  19. On the 16-bit ISA bus IRQ2 is elevated to which higher level Interrupt?
  20. On the PC side the printer port is a:
  21. opically how many type III PC cards can you insert in a laptop
  22. Pick the correct choice for the 80386SXCPU.
  23. Resistance is measured in ?
  24. Suppose that you have a the maintenance package identifies several possible field replaceable units (FRUs) that will resolve the problem. What should you do after turning the power off?
  25. The mouse pointer moves erratically what is the possible cause? The mouse
  26. The terms "red book" "yellow book" and "orange book" refer to:
  27. to view any currently running Terminate Stay Resident (TSR's) programs you could type:
  28. To view any currently running Terminate Stay Resident (TSR's) programs you could type:
  29. Voltage is measured:
  30. What beep codes could indicate a system board or power supply failure?
  31. What could cause a fixed disk error.
  32. What is the best ground for a conductive work bench?
  33. What is the highest binary number that can be referred to on a three position jumper block?
  34. What product is used to clean smudged keys on a keyboard?
  35. What tool is used to test serial and parallel ports?
  36. When installing a SCSI CD-ROM drive you must set the CD-ROM SCSI adapter to:
  37. When installing PCI NICS you can check the IRQ availability by looking at
  38. Which Motherboard form factor uses one 20 pin connector
  39. Which part of the laser printer should NOT be exposed to sunlight?
  40. Which peripheral port provides the FASTEST throughput to laser printers?
  41. Which provides the fastest access to large video files?
  42. Which standard govern parallel communications?
  43. Which type of system board is the MOST likely candidate for processor upgrading if you want maximum performance and future compatibility?
  44. With respect to a network interface card the term 10/100 refers to
  45. You have a system that periodically locks up. You have ruled out software and now suspect that it is hardware. What should you do first that could help you narrow it down to the component at fault?
  46. You just installed a new IDE hard drive but your system BIOS will not recognize the new drive what should you check first.
  47. Your customer tells you the print quality of their dot matrix printer is light then dark. Which of the following could cause the problem.
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!